邹亮;潘清林;何运斌;王昌臻;梁文杰;李文斌;

• 1:中南大学材料科学与工程学院
• 2:中南大学材料科学与工程学院
• 3:中南大学材料科学与工程学院
• 4:中南大学材料科学与工程学院

摘要(Abstract)：

采用铸锭冶金法制备了5种不同Sc含量的超高强Al-8.1Zn-2.3Cu-2.05Mg-0.12Zr合金,利用光学显微镜和透射电镜以及扫描电镜分别观察了合金的显微组织与断口形貌,测试分析了合金的拉伸力学性能。结果表明:采用Sc微合金化,凝固过程中形成的初生Al3(Sc,Zr)粒子可显著细化合金铸态晶粒组织,消除枝晶偏析,均匀化过程中形成的次生Al3(Sc,Zr)粒子可抑制合金的再结晶,并强烈钉扎位错及亚结构;微量Sc的添加使合金强度提高26～94MPa,同时保持较高的伸长率,合金拉伸断口表现为层状和韧窝混合型形貌特征,合金中适宜的Sc添加量为0.21%。

关键词(KeyWords)： Al-Zn-Cu-Mg-Zr合金;Al3(Sc,Zr)相;微观组织;力学性能

Abstract:

Keywords:

基金项目(Foundation): 国家863高技术新材料课题(2006AA03Z523)资助项目

作者(Author): 邹亮;潘清林;何运斌;王昌臻;梁文杰;李文斌;

Email:

DOI:

参考文献(References)：

• [1]Lukasak David A,Hary Ray M.Strong aluminumalloy shaves airframe weight[J].Advanced Materials&Processes,1991,(10):46.
• [2]Luckasak D A,Hart R M.Aluminumalloy development effortsfor compression dominated structure of aircraft[J].Light Metal Age.,1991,(10):11.
• [3]Lengsfeld P.Microstructure and mechanical behavior of spray deposited Zn modified7xxx series Al alloys[J].International Journal of Rapid Solidification,1995,8(4):237.
• [4]Desanctis M.Structure and properties of rapidly solidified ultra-high strength Al-Zn-Mg-Cu alloys produced by spray deposition[J].Materials Science&Engineering A,1991,141(1):103.
• [5]Wu Yilei,Froes F H.Microstructure and properties of a new superhigh-strength Al-Zn-Mg-Cu alloy C912[J].Materials and Design,1997,18(426):211.
• [6]杨遇春.大有作为的含钪铝合金[J].金属世界,2004,1:34.
• [7]曾渝,尹挚民,潘青林.超高强铝合金的研究现状及发展趋势[J].中南工业大学学报,2002,6(33):592.
• [8]Milman Yu V,Lotsko D V,Sirko OI.Sc effect of i mproving mechanical properties in aluminiumalloys[J].Materials Science Forum,2000,1107.
• [9]Rokhlin LL,Dobatkina TV,Bochvar NR,et al.Investigation of phase equilibria in alloys of the Al-Zn-Mg-Cu-Zr-Sc system[J].Journal of Alloys and Compounds,2004,(367):10.
• [10]Chinh N Q,Kovacs Zsolt.Precipitation in Al-Zn-Mg-(Cu,Zr)alloys[J].Zeitschrift fr Metallkunde/Materials Research and Advanced Techniques,1997,88(8):607.
• [11]Yin Zhi min,Pan Qinglin,Zhang Yonghong,et al.Effect of minor Sc and Zr on the microstructure and mechanical properties of Al-Mg based alloys[J].Materials Science and Engineering,2000,A280:151.
• [12]Yin Zhi min,Yang Lei,Pan Qinglin,Jiang Feng.Effect of mi-nor Sc and Zr on microstructures and mechanical properties of Al-Zn-Mg based alloys[J].Chinese Journal of Nonferrous Metals,2001,(11):822.
• [13]Rabinovich M Kh,Markushev M V.Influence of fine-grained structure and superplastic deformation on the strength of alumini-umalloys[J].Journal of Materials Science,1996.4997.
• [14]Costello F A,Robson J D,Prangnell P B.The effect of small scandium additions to AA7050on the as-cast and homogenized microstructure[J].Materials Science Forum,2002.757.
• [15]Norman AF,Prangell P B,Mcewen RS.The solidification be-havior of dilute aluminumscandium alloys[J].Acta.Mater.,1991,46(16):5715.
• [16]Schneibel J H.Crystallography of cleavage fracture in Al3Sc[J].Mater.Res.,1992,7(4):868.